[User Guide] RRCM7500 Operating and Programming Instructions

Click here for Printable Instructions and Code List

This article applies to the Anderic RRCM7500 Universal remote control. 

Compatibility

• This remote control is specifically designed to work with Channel Master DVR set-top boxes, including the models CM7001, CM7004, CM7500GB16, CM7500TB1, and CM7500XRC2. 
• The Anderic RRCM7500 is not programmable for any other DVR models. 
• Additionally, the RRCM7500 allows you to program secondary devices, such as TVs and audio equipment, however it is not designed to replace your TV or Audio original equipment remotes.

Installing Batteries

Note: We provide a screw packed inside the battery compartment, this can be used to secure the battery door to the remote, see the below diagram, but is optional.

1. Slide the battery cover down toward the bottom of the remote to remove it, then replace it after installing the batteries.
2. Please insert two AA batteries into the battery compartment behind the battery door on the back of the remote.

Note: Please make sure to match polarities when installing the batteries.

Optional security cable (sold separately)

This remote features an optional security cable attachment (sold separately). You can purchase this security cable from Anderic.com. Part number: CBL01. 

Programming Instructions

Code Input Method 

Use this method to program your remote for limited functionality for TV/Audio equipment.

1. Turn on the device you want to control.
2. Find the corresponding brand code from the attached code list and write it down.
3. Press & hold the [SETUP] key for about 3 seconds until the indicator light remains on; release the key
4. Input the 4-digit code from the code list.
   1. If valid, the indicator light will turn off immediately.
   2. If the code is invalid, the indicator light will blink three times quickly and then turn off; please try entering the code again.
5. Check to see if most of the keys work to control your device. If not, please try another code under the same brand and repeat all steps. You may also try the “Code search method.”

Note: If no button is pressed for 20 seconds during programming mode, the remote will exit programming mode. 

Code Search Method 

This method is used to program the remote to your TV/Audio Equipment without using codes, This method may take longer than the Code Input Method.

1. Turn on the device you want to control.
2. Press and hold the [SETUP] key for approximately 3 seconds until the indicator light remains on; then release the key.
3. Press and hold the [RED-COLORED] (for TV) key or the [GREEN-COLORED] key (for audio); it will enter the “Code search method.”
4. Release the key [RED-COLORED] (for TV) or the [GREEN-COLORED] key (for audio) when the device responds.
5. Check to see if most of the keys work to control your device; if not, please repeat all steps above. 

One-button Search Method

This method is used to program your remote to TV/Audio equipment without using the full code list. This method is a bit easier than the Code Search Method.

1. Turn on the device you want to control.
2. Press and hold the [SETUP] key for approximately 3 seconds until the indicator light remains on; then release the key.
3. Input code 991(for TV) or 992 (For AUDIO).
4. Find your corresponding brand number from the list below, and press and hold the corresponding number key.
5. Once the unit responds, release the key and press any key to save. 

Additional Options

Input Lock

Note: This feature always locks the input key to send the code to the programmed TV or Set-Top Box device, regardless of the selected mode. Enable this option if you want the INPUT key to always work the TV or the Channel Master.

1. Press and hold the [SETUP] key for approximately 3 seconds until the indicator light remains on; then release the key.
2. Press the [INPUT] key, and the indicator light blinks once and remains illuminated.
3. Press the device key [RED-COLORED] for the TV or [GREEN-COLORED] for the set-top box. 

Volume Lock

Note: This feature allows locking the VOL+, VOL-, and MUTE keys to always send the code to the programmed TV or set-top box device regardless of the remote’s mode.

1. Press and hold the [SETUP] key for approximately 3 seconds until the indicator light remains on; then release the key.
2. Press the [VOL+] key, and the indicator light blinks once and remains illuminated.
3. Press the device key [RED-COLORED] for the TV or [GREEN-COLORED] for the set-top box. 

Code Protection

Note: This feature allows for locking the codes programmed in place, requiring an extra step to avoid accidentally having the codes changed.

1. Press and hold the [RED-COLORED] key and the [OK] key simultaneously for about 3 seconds, until the indicator light flashes twice; then release the keys.
   1. Enabled: Code input or code search method cannot change the device code 
   2. Disabled: Code input or code search method can program the code as usual. Repeating these steps will toggle between enabled and disabled states. 

Reset to factory default status

1. Press and hold the [OK] key and the [YELLOW-COLORED] key simultaneously for about 3 seconds, until the indicator light flashes once; then release the keys. 

Low voltage indication 

If the LED indicator flashes ten times when you press any key, it indicates the low voltage. Please replace the batteries. 

Combo Power off/on:

This is enabled by default.

This option toggles the remote's ability to combine the power of all programmed devices with one press of the Power ON/OFF keys. If you would like to deactivate or activate this feature, follow the following steps:

1. Press and hold the [OK] and [ON] keys simultaneously, the indicator light flashes twice; then release the two keys. 

Backlighting feature: 

Note: Deactivating the backlighting feature will conserve battery consumption.

1. Press and hold the [OK] and [BLUE-COLORED] keys simultaneously for about 3 seconds, until the indicator light flashes twice; then release the two keys. 

Code List

CLICK HERE TO VIEW THE CODE LIST